Workplace health, safety, risk and emergency training · In person and onlinePartner program1800 231 173
Orana Skills Centre

Workplace Exposure Limits Start 1 December: What Changes and What To Do Now

Workplace Exposure Limits Start 1 December: What Changes and What To Do Now

On 1 December 2026 the list Australian workplaces have used for years to judge airborne contaminants changes. The Workplace Exposure Standards (WES) become the Workplace Exposure Limits (WEL). Until 30 November the old standards still apply. From 1 December, the new limits do.

If anyone at your workplace breathes in dust, fumes, vapours or gases from the work, this affects you. That covers far more than chemical plants: workshops, construction sites, cleaning, agriculture, mining, laboratories, healthcare and anywhere engines run indoors.

What is actually changing

The name, and what it signals. "Limit" replaces "standard" on purpose. Work health and safety ministers agreed to the rename to make it clear these are levels that must not be exceeded, and to line up with the terms used overseas. An exposure limit is a ceiling, not a target.

The numbers. Hundreds of substances have a revised value, and most of the changes are to a lower limit. Some common contaminants are affected, so a result that was comfortably under the old standard may now sit close to, or over, the new limit.

New substances. Substances have been added to the list, including diesel particulate matter. If you run diesel engines, generators, forklifts or plant in enclosed or underground areas, it now has its own limit.

Some carcinogens no longer have a number at all. A group of cancer-causing substances that can damage DNA no longer has a numerical limit. That is not a relaxation. It reflects that there is no known safe level of exposure, so exposure must be eliminated or kept as low as reasonably practicable.

Codes of Practice updated to match. Safe Work Australia published revised versions of 15 model Codes of Practice on 12 November so they refer to the new limits.

Does it apply in my state?

Most jurisdictions are moving to the new list from 1 December, but each state and territory adopts it through its own laws, and the details differ:

  • Victoria is adopting the list from 1 December, with a longer transition for a group of 15 substances until 2029.
  • NSW has confirmed Workplace Exposure Limits replace the standards from 1 December.
  • Other states and territories have their own arrangements and some transition periods. Check your regulator's website for the exact position where you work.

If you work across borders, check each state you operate in.

Who needs to act

You need to look at this now if you:

  • keep a hazardous chemicals register or rely on safety data sheets (SDS)
  • do air monitoring or have results from previous monitoring
  • run health monitoring for workers exposed to substances such as silica, lead or isocyanates
  • use respirators as a control, because the protection factor you chose was based on the old numbers
  • run engines indoors, cut or grind stone, concrete or timber, weld, spray, or decant chemicals

A short checklist before 1 December

  1. Update your chemical register. Check each product against the new list, and note any substance with a lower limit, a new limit, or no numerical limit.
  2. Look at your monitoring results again. A result that passed under the old standard may not pass under the new limit. If you have no monitoring and there is doubt about exposure, arrange it.
  3. Review your risk assessments. Where exposure is now close to or over a limit, move up the hierarchy of control: eliminate or substitute the substance, enclose the process, improve local exhaust ventilation, and keep PPE as the last line.
  4. Check your respiratory protection. Make sure the type of respirator, fit testing and change-out still match the new limits.
  5. Check the SDS you rely on. Older safety data sheets will still quote the old standards. Ask suppliers for current versions.
  6. Tell your people. A short toolbox talk on what has changed, and what you are doing about it, builds trust and gets the right questions asked.
  7. Plan for diesel. If diesel engines run in enclosed or underground areas, include diesel particulate matter in your monitoring and controls.

Where we can help

If you are not sure where your workplace stands, talk to us. This article is a general guide, not legal advice: always check the current Workplace Exposure Limits list and your regulator's guidance for where you work.

Want to keep up to date with WHS news? Subscribe to our mailing list

Related products and courses

Health and Safety LegislationWorkplace Health and SafetyHealth Management